Manufacturer of polypropylene pipes. Production of polypropylene pipes and the necessary equipment for production

To consider the topic of the manufacture of polypropylene pipes and fittings for water supply and heating pipelines, it is necessary with a preliminary detailed description of the materials used for production.

Polypropylene pipes and fittings have a lot of advantages that distinguish them from their steel counterparts:

• they are much lighter;
• not susceptible to corrosion;
• do not grow inside during use;
• do not create vibration and rumbling, as well as other noises;
• do not burst when the water in the system freezes;
• do not conduct electricity;
• do not need painting;
• very easy to work with.

Pipes and fittings made of polypropylene can work for decades. These are environmentally friendly products that are successfully used for pipelines of any complexity. Therefore, their production and manufacture is widely established throughout the world.

The use of fittings with chrome and brass inserts allows combine these blanks with steel pipes.

The construction of these materials is very tight, and this application brings tangible economic benefits.

Polypropylene is the initial product of the polymerization of propylene and ethylene in specific quantities. The resulting material is named random copolymer PPRC.

In the domestic market today there is no worthy analogue to foreign polymers. We use Finnish RA 130E BOREALIS and Hungarian TIPPLEN CS4-8000 TVK for the manufacture of polypropylene pipes.

The essence of the pipe manufacturing process is simple, and it is not very laborious. Speaking about it, the following features should be highlighted:

• low energy costs in manufacturing;
• ecological safety;
• for the production, installation and use of one set of a line for the production of polypropylene pipes and fittings, a lot of space is not needed (this is approximately 100 m 2);

The set of polypropylene pipe extrusion line is a complete cycle of extrusion, calibration, cooling, drawing, etc.

Raw material for work

They are of the following types:

1. Polymers of low and high pressure.
2. PVC;
3. Polypropylene;
4. Polybutylene.

Types of equipment for manufacturing

Equipment for the production of polypropylene pipes (extruders) are machines of the following types:

• Screw. They function like a juicer or meat grinder.
• Screwless. They are used for the production of blanks from mixed materials. The disc becomes the main detail in these mechanisms.
• Combined. In these mechanisms, the screw part is combined with a disk.

IMPORTANT! Screw type machines are considered the most common equipment for the production of plastic products.

Lines for the production of plastic pipes, in addition to the extruder, also have the following equipment:

1. Raw material supply system.
2. A machine that cuts blanks.
3. Capacity for calibrations and cooling.
4. Pulling mechanism.
5. Mixer.
6. Conveyor tape.
7. Vacuum forming.
8. Accumulating mechanism that performs the stacking of blanks.

Raw material selection

When choosing raw materials, they opt for a granular polymer, but you need to carefully look at its shelf life.

And polypropylene and polyethylene are practically not limited by these indicators, which makes it more convenient to use.

From an economic point of view, an advantageous copolymer and HDPE.

IMPORTANT! When opening your own production for the manufacture of polypropylene pipes and fittings, it is advised to maintain cooperation with one supplier. Because the change of raw materials requires the change of equipment for the production of polypropylene products.

Manufacturing process

The main equipment that processes raw materials and turns them into a polypropylene pipe or fitting is called an extruder. And the production itself takes place in the following sequence:

• Raw materials for the manufacture of pipes and fittings are fed into a special chamber. It is in small granules or comes in the form of chips. Also, secondary raw material that has undergone preliminary processing (grinding) is often taken into work. Secondary raw materials are mixed with the main.
• Using electric or gas heating, the poured mass is melted. Temperature indicators in this case range from 230 to 250 degrees. But at the same time, it does not turn into a liquid, but only becomes viscous. So that this viscous heated mass does not stick to the walls of the apparatus, they are coated with Teflon.
• Next, the extruder extrudes the blanks from the thick mixture according to the set size. Usually the length of the workpiece is two and a half meters. The equipment performs all these actions very quickly and completely offline. Human intervention is only required to set the right parameters for the job. The best equipment for the production of polypropylene pipes and fittings is capable of producing up to 200 kg of products per hour.
• The next step is the cooling of the blanks. To do this, they are placed in a container for cooling. The cooling process takes a couple of minutes. Then he perfectly holds the given dimensions. In the cooling tank, the plastic undergoes a shaping process, during which the material is thoroughly rounded and takes on the desired shape.
• At the end of the technological process of production, a marking is applied to the products, which displays the parameters of the operation of the products, here the batch number and the date of production of the product are put down. Then the blanks are packaged, packaged and sent to storage facilities or to consumers.

Video

Often they are produced at the same enterprises as pipes.

Only for the production of polypropylene fittings it is necessary to install additional equipment (machine).

It does not occupy a large amount of space, but it makes it possible to increase the range of products. For companies, this becomes an important factor, especially in a highly competitive environment.

The main problems and difficulties of production

Almost all countries of the world produce building materials. This also applies to polypropylene pipes and other plastic products, the manufacture of which is excellently established in Russia.

The main problem of the industry lies in the fact that domestic investors are not very active in financing the purchase of new modern equipment.

Many enterprises have to act on old technologies that are losing their relevance at the moment.

One-time capital expenditures could be the key to high profits in the future. But, they don't. Therefore, they cannot create worthy competition to foreign analogues.

There are no external differences, if we compare our and foreign polypropylene products. But, practical use shows different results.

Video

Domestic blanks do not tolerate wear as much, are not as durable, and often have surprises in the form of marriage, which cause a breakthrough.

For the above reasons, consumers often prefer more expensive, but high-quality products from German and Turkish manufacturers.

Video

And in the end, it should be added that the production of polypropylene pipes has been turned into an automated production that does not require huge energy and labor costs. Also, this production has almost no waste and does not harm the environment.

In recent years, the number of manufacturers supplying polypropylene pipes to the Russian market has grown significantly.

This is due to several factors, but only two are of particular importance:

• Increasing consumer demand for this type of product.
• A simple technology for the production of polypropylene pipes.

Many modern Russian entrepreneurs strive to become producers of polypropylene pipes. However, at many enterprises these tubular products are produced in parallel with other products.

The main manufacturers of polypropylene pipes in Russia

Production of PP pipes on site Russian Federation carried out by hundreds of enterprises. However, only a few are popular.

• The largest Moscow company "Sinicon" is engaged in the production of plastic products intended for the installation of hot and cold water supply systems, as well as for sewer systems.
• Two large factories of the YarInterPlast company, one of which is located in the south of Russia, and the other in Yaroslavl, specialize in the production of reinforced plastic pipes, various connecting elements for water supply and sewerage systems.
• The Russian enterprise Ikaplast has been supplying components to the Russian market for 10 years, with the help of which the installation of water pipelines, gas pipelines and chemical pipelines is carried out. These systems require high quality plastic products, therefore, before delivery, all parts undergo various tests in modern laboratories belonging to the enterprise.
• The largest Russian company "Polytron". The introduction of modern technologies allows the production of high quality polypropylene pipes. In addition, the company has launched the production of fittings and systems made of polypropylene, which is not subject to rapid ignition.
• The Almetyevsk Pipe Plant has launched the production of pipes from both propylene and high-quality steel.
• Kosmoplast is the largest supplier of fittings to the Russian market. In addition, the production of sewer and water systems, as well as polypropylene parts, is carried out here.

The list of the main enterprises for the manufacture of polypropylene tubular products and related parts does not end there. In Russia, a huge number of companies working in this area.

Distinctive features of polypropylene products

The popularity of such products is due to many reasons, among which the most important are positive characteristics polypropylene:

• Polypropylene parts are highly durable.
• The material does not rust or rot.
• Polypropylene withstands large temperature differences.
• It does not affect the quality and taste properties of water.
• Has a very long service life.
• It has a significantly lighter weight compared to metal counterparts.
• Lower cost due to easy way manufacturing.

Manufacturing technology

The main work on the production of polypropylene products is carried out on a special machine for the production of polypropylene pipes, which is called an extruder. Such equipment performs multi-stage processing of the material, which subsequently becomes a pipe.

The technology for the production of polypropylene pipes involves the following stages of work:

1. Procurement of raw materials in the required quantities.
2. Placement of polypropylene, which has the form of granules or chips, in a special chamber. In some cases, secondary material is added to the main raw material.
3. At a temperature of 250 0 C, the raw materials melt with the formation of a viscous plastic substance. Thanks to the Teflon coating on the inner surface of the chamber, molten plastic does not stick to the walls.
4. In the extrusion process, products up to 2.5 meters long come out of the extruder.
5. The blanks are placed in special cooling baths. Thanks to this, the shape of the products is preserved for a long time.
6. At the last stage, polypropylene pipes are marked, packaged and stored.

Equipment for the production of pipes from polypropylene works offline, and the whole process takes place within a short period of time. The operator monitors the operation of the machine. He also sets the necessary parameters and troubleshoots the problems that have arisen. The average productivity of the best Russian machines is about 200 kg per hour. A typical plant producing plastic products in Russia can produce more than 1,000 meters of pipe.

Equipment for the production of pipes from polypropylene

The manufacture of each type of pipe is carried out on its own production line. Each line consists of special units.

Russian enterprises for the production of polypropylene pipes use the following machines and devices:

• The different-sized batchers measuring and giving raw materials.
• Machine for polypropylene pipes, as the main means for the manufacture of material.
• Device for pulling and feeding the pipe into the cooling chamber.
• Cooling system baths.
• Machines that perform the calibration of finished tubular products.
• A device that measures and cuts the finished product.
• Equipment for labeling and packaging.

raw material

The main types of raw materials used in Russia are:

• propylene homopolymer. It is suitable for the production of polypropylene pipes and fittings for sewage system.
• Random propylene copolymer is a foreign raw material, which is necessary in the manufacture of pipe products for heating and water supply systems.

The process of production of polypropylene occurs automatically from the operation of filling the granules into the bunker, to the exit finished products. All extrusion line equipment is controlled from one command unit. You just need to download the program for heating the material, transferring it from one mechanism to another, and all other operations will take place automatically. The accuracy of the specified dimensions of the pipe diameter occurs in a vacuum calibrator. The principle of setting the accuracy of geometric dimensions is as follows: the pipe enters the device. It is fixed along the outer diameter and locked on both sides in the vacuum calibrator. Since the two covers of the device are connected using rubber gaskets, the coolant cannot leak out. After that, cold water is supplied from the nozzles under pressure to the device, the material is finally cooled and hardened.

A photo

Firms

Production of polypropylene pipes.

In the field of market relations, the main principle of which is based on a competitive price / quality ratio, the release of products, which, in comparison with analogues, is a unique offer for the consumer, naturally leads to high and stable profits. The production of polypropylene pipes is one of the most profitable areas for investment today. This statement is correct based on two factors. The presence of a growing demand for tubular products and high quality polypropylene pipes at a relatively low cost.

The high demand for pipes is determined by the construction of new facilities, both residential and industrial sectors, and the need, which is becoming acute in the next decade, to replace old metal pipe systems with new ones. The fact is that most of the water and sewer systems of the countries of the former Soviet Union, due to corrosive wear, need to be replaced for a long time. Polypropylene pipes are not only a more cost-effective alternative to metal pipes, but in many respects they win in quality, because due to their flexibility they can withstand significant overloads associated with the most extreme temperature regime Plus, it's easier to install.

Pipe production line

Main Devices:

SJ-65/30 extruder - 2 pcs
SJ-50/30 extruder - 1 piece
SJ-25/25 extruder - 1 piece
Set of extrusion heads and calibrators.
Vacuum calibration chamber.
Cooling chamber
Pulling device.
Cutting device.
stacker

The main advantages of PP pipes reinforced with fiberglass compared to standard PP pipes:

the coefficient of linear expansion is 75% less (compared to conventional polypropylene pipes);
no mandatory stripping is required (for pipes reinforced with aluminum foil);
due to the small linear expansion, the distance between the fasteners increases, which reduces the total number of supports and reduces the cost of installation;
fiberglass layer provides pipe strength with a smaller wall thickness;
conditional passage is increased by 18%;
simple and quick installation of the pipe.

DIY

Lines for PP-R pipes

The rapid development of the plastic pipe market is due to moral and wear and tear iron and steel pipes. Polymer pipes are the optimal replacement for most metal pipeline networks. Polypropylene pipes are used in heating and water supply systems. For the production of pipes, high-quality heat-resistant polypropylene is used. It is polypropylene that is the most competitive material compared to copper, steel, etc.
Polypropylene pipes:

wear-resistant
resistant to aggressive environments,
environmentally friendly,
not subject to corrosion
do not overgrow with carbonate and other deposits.

The service life of PP-R pipes is up to 50 years in cold water supply systems and up to 25 years in hot water supply systems. In addition, the ease, simplicity and reliability of installation can reduce labor costs by several times compared to the installation of metal pipes.

The lines are equipped with:

Single screw extruder
High Speed ​​Tubing Heads
Vacuum calibrator
Water cooling section
pulling device
Cutting device
Markirator
Storage device

Polymer pipes are widely used in various fields. They are used in the transportation of drinking water, technical liquids (solutions of acids, alkalis, salts, mineral fertilizers); gas transportation and gas mixtures; when laying various types sewers; in the protection of power cables; in heating and reclamation systems; as waterproofing shells for heating mains; and also as shaping in monolithic housing construction.

A wide range of applications of polymer pipes is explained by durability, corrosion resistance, low thermal conductivity, environmental friendliness, and new laying possibilities.
Polymer pipes are made from HDPE, LDPE, cross-linked polyethylene, polypropylene and copolymers of propylene, polybutene, PVC.

Pipes made of polymeric materials are mainly produced by continuous extrusion. The main element of the pipe line is a screw extruder (single screw for HDPE, LDPE and PPS, twin screw for PVC). In the production of polyethylene and polypropylene pipes, granular polymer compositions are used.

Today, all over the world, especially in developed countries, polymer pipes occupy a leading position in the construction of water supply, sewerage and heating systems.

The main consumers of polymer pipes are construction and installation organizations, housing and communal services, as well as private developers and construction teams.

Based on world experience, we can conclude that in the near future the growth rate of consumption of polymer pipes will not be lower than in recent years, and the trend of replacing metal pipes with non-metallic ones will continue.

Implementation of the project is possible at JSC "Maloritskaya rayagropromtechnika" (Brest region, Malorita).

Equipment

Extrusion line for the production of polypropylene (PPR) pipes

The reliability and durability of pipeline systems directly depend on the quality and properties of the source material and, of course, on the machine itself on which the tube was produced. The company "Global Group" is engaged in the supply of equipment for the production of polypropylene pipes (PPR). The machines of our company will help to significantly increase the efficiency of manufacturing due to high productivity and cost-effectiveness. We offer reliable extrusion lines made of quality materials, which, if used correctly, will last for a long time.

The emergence in the last decade of new polymeric materials has led to revolutionary changes in industrial and residential construction, in the installation and maintenance of utility systems. Polypropylene is a colorless thermoplastic polymer material. Along with many other products made from this material, pipes and fittings (connecting part) made of polypropylene (PPR) are widely used, which have a number of advantages, which makes them ideal for creating pressurized water supply and heating systems.

Benefits of products produced by the machine for the production of PPR pipes and fittings

Compared to metal products, PPR tubes have a number of advantages that have led to such a high demand for them in recent years:

Easily transported, transported, which reduces the cost of their loading and unloading;

Easy to install;

Safe for health;

Low installation cost due to the high weldability of propylene;

The service life is 3-4 times higher than the same characteristic of metal counterparts;

Unlike steel, plastic is a material that is resistant to corrosion (does not rust or deform);

Easily withstand sharp temperature fluctuations, they are reliable in winter and never break;

Excellent permeability and resistance to various chemical environments;

Polypropylene pipes for heating and other communication plastic systems have excellent sound insulation.

Short description:

The process of production of polypropylene occurs automatically from the operation of filling the granules into the bunker, to the output of the finished product. All extrusion line equipment is controlled from one command unit. You just need to download the program for heating the material, transferring it from one mechanism to another, and all other operations will take place automatically.

Production of material for polypropylene pipes. Any production of polypropylene pipes begins with filling granulated polypropylene into a special bunker. Here the material is melted, the entire cylindrical device is divided into sectors, in each of these departments a certain, strictly controlled temperature is set. Since the screw of the device is constantly rotating, the granules of the substance are mixed and melted. At the exit of the device through special forms under high pressure a polypropylene pipe is formed.

The shaping of the product takes place in the extrusion head. It is here that the molds are installed to limit the inner and outer diameter of the product. The head itself is attached to the hopper cylinder with a flange.

The process of production of polypropylene occurs automatically from the operation of filling the granules into the bunker, to the output of the finished product. All extrusion line equipment is controlled from one command unit. You just need to download the program for heating the material, transferring it from one mechanism to another, and all other operations will take place automatically.

The accuracy of the specified dimensions of the pipe diameter occurs in a vacuum calibrator. The principle of setting the accuracy of geometric dimensions is as follows: the pipe enters the device. It is fixed along the outer diameter and locked on both sides in the vacuum calibrator. Since the two covers of the device are connected using rubber gaskets, the coolant cannot leak out. After that, cold water is supplied from the nozzles under pressure to the device, the material is finally cooled and hardened.

In addition to the cooling bath, pipe calibration is carried out by means of a pulling device. In addition to the accuracy of the outer diameter, polypropylene pipes have accurate wall thickness measurements, so by pulling the part, the guarantee of its inner diameter is also controlled.

The final stage of production of PP pipes. The complete production of polypropylene pipes implies the receipt of a marketable product, that is, the required technical indicators and geometric dimensions.

After specifying the exact dimensions of the pipe diameters, the process of cutting them into measured lengths begins. This operation takes place using either guillotine shears (product diameter up to 50 mm), or using circular saws.

The advantage of the second cutting method is the high quality of the pipe end obtained in the process of cutting. When using the same guillotine, the end of the PP product becomes substandard (slightly flattened).

Technology and raw materials for the production of pipes

For the manufacture of plastic pipes, various raw materials are used: high and low pressure polymers, polypropylene, polybutene, polyvinyl chloride, etc. Their production is environmentally friendly and uncomplicated, it is based on extrusion. Extrusion is the extrusion of pipes from molten plastic using a special machine (extruder). There are several types of extruders: screw, screwless and combined. The principle of operation of a screw extruder resembles a meat grinder, or a juicer. For screwless, the main working part is the disk; they are used, if necessary, for the production of pipes from mixed materials. The combined extruder combines both the screw part and the disc. The most commonly used screw extruders. They are single- and double-stage, specialized and universal, single- and twin-screw, equipped with a degassing chamber and without it, with screws rotating in one or in opposite directions, etc.

The production of plastic pipes is as follows. Raw materials in granules are filled up in the hopper-receiver of the extruder, where under high temperature it melts. Next, the mass is squeezed out through the forming head of the extruder, which determines the parameters of the future pipe. After the initial molding, the pulling machine pulls the billet into the primary cooling bath, where it is finally shaped under pressure by means of a sizing mold. Next, the pipe is cut and either stacked (large-diameter pipes) or coiled (small-diameter pipes).

Equipment and raw materials

The full-cycle plastic pipe production line, in addition to the extruder, includes a pipe cutting machine, a raw material supply system, calibrating and cooling baths, a mixer, a pulling device, a conveyor belt, a vacuum former and a pipe stacker.

Productivity depends on the size of the pipe: pipe diameter - 20.25, - 80 kg / h, pipe diameter - 32.40.50 - 100 kg / h, pipe diameter - 63.75,90,110 - 130 kg / h. The line can produce about 1000 meters of pipes per day, depending on the diameter. The lines have different parameters, so you can order machines for your business, or you can save money and buy used equipment. The lowest cost of such a set is about 400 thousand rubles.

Granular polymers are purchased for raw materials. It is important to be demanding on its quality and shelf life. Polyethylene and polypropylene are very advantageous materials due to their almost unlimited shelf life. Polypropylene copolymer is one of the the best materials for the manufacture of pipes. Its cost is about 50-70 rubles per kg. Low-pressure polyethylene (HDPE) is also often used for production, its cost is lower - about 32 rubles per kg and more. The best option will arrange the supply from one plant, because the change of raw materials will require a change in the characteristics of the equipment.

Premises and staff

For the production of plastic pipes, any room outside the city is suitable, which has a convenient entrance, in which you can locate a workshop, a large warehouse, a bathroom, and premises for staff. All equipment can be located in the workshop area from 40 sq.m to 200 sq.m. For its maintenance, you will need from 3 people per shift. It is necessary to hire technologists, machine operators, auxiliary workers. The average salary of a technologist is about 50 thousand rubles, workers - about 25-30 thousand rubles.

Requirements

To open production, you will need to obtain permits from the gas service, the fire inspectorate, the sanitary and epidemiological station, the local division of Gosnadzorohrantrud, local executive authorities, etc.

According to GOST 18599-2001, the conditions for transportation and storage of plastic pipes are as follows.

It is allowed to transport pipes by any means of transport in covered bodies (wagons). To protect the pipes from dust and external influences, they must be closed with plugs and placed in a package. The mass of spools of pipes together with packaging should not exceed 1.25 tons, the length of pipes - no more than 5.5 m.

Store pipes in warehouses in a horizontal position away from sun rays and heating appliances. The height of the stack when storing pipes for more than 2 months should not exceed 2m. When stored for up to 2 months, the height of the stack should be no more than 3m. Storage of pipes is possible no more than 12 months. Shelf life - 2 years from the date of manufacture.

The main advantages of polypropylene pipes

Durability of operation

The service life of the pipeline is 25-50 years, depending on the temperature and pressure during operation. Polypropylene pipelines meet the functional requirements of SNiPs and can be used for transportation cold water under pressure up to 2.0 MPa (20 atm), while ensuring the pipeline service life of at least 50 years.

When transporting hot water under pressure up to 0.6 MPa (6 atm) and constant exposure to a temperature of 60°C, the durability of the pipeline is also 50 years, and with an increase in the operating constant temperature to 75°C - 25-30 years. You can read more about service life here.
Constant pressure Pipes made of polypropylene do not overgrow throughout the entire service life. This is achieved due to the high purity of the inner surface of the pipes (0.003-0.005 mm), as well as the chemical inertness of the material.

Highest Reliability

Polypropylene pipes "TransFormer" are absolutely homogeneous and with temperature changes the entire pipe array behaves in the same way, which ensures the absence of internal stresses during operation. The connection of polypropylene pipes with fittings is carried out by polydiffusion thermal welding at a temperature of 260°C without the use of flame. You can read more about the welding process here. Thanks to this method, a connection is formed that does not differ at all from the array of the pipe itself.

Thus, the uniformity of both the pipe itself and the connections of polypropylene pipes with fittings ensures the highest reliability of the entire system, which, of course, is one of the main advantages of using polypropylene pipelines. It is thanks to the highest reliability that polypropylene pipes have become so widespread throughout the world.
Also, polypropylene pipes are distinguished by: low weight (4-7 times lighter than metal pipes), high culture, manufacturability and installation speed (it takes only about 12 seconds for one connection of 20 mm in diameter), the absence of the “defrosting” effect when the system freezes, high noise and vibration absorbing ability.
Pipes "Transformer" do not conduct current, are white and do not require painting after installation. The smooth outer surface of pipelines makes it possible to remove from them dust and dirt that enters during installation and operation. If necessary, the pipes can be hidden in the walls.
The cost of a system of polypropylene pipes "TranFormer" is significantly lower than the price of pipeline systems made of metal and metal-plastic, with higher performance. You can see a comparison of the cost of pipes here.

From the technological side, the production process is quite simple, with minimal energy consumption, labor-intensive and environmentally friendly. The production line is a continuous, technologically complete cycle.

This line consists of:

• extruder;
• vacuum water baths;
• cooling baths;
• pulling device;
• cutting device;
• receiving tray;
• winding.

The line is equipped with a circular saw (or planetary saw) and has high productivity and excellent reliability. The planetary saw has automatic digital control: it is simple and reliable. Equipment for the production of polypropylene pipes meets international quality standards.

Pipe lines are completed with special devices in accordance with the parameters of the manufactured products. Depending on the productivity and purpose, the lines can be equipped with loaders, dryers, various sets of tools (corresponds to a certain standard size). Depending on the additional conditions, additional accessories are required accordingly. For example, if you want to produce products with a color stripe, then you need a co-extruder. If marking is required, then a marker is used, etc.

Materials for the manufacture of polypropylene pipes are: polypropylene random copolymer, polypropylene homopolymer, polyethylene, polyvinyl chloride. These materials must be considered when choosing: for indoor or outdoor use. For example, polypropylene homopolymer becomes brittle at temperatures below zero degrees. Therefore, they must be used for internal pipelines. But polyvinyl chloride is suitable for outdoor sewerage, as it has high performance at low temperatures.

The following steps are included in the production:

After the production process, finished products are packed and stacked for further sale.

Application area.

The scope of polypropylene pipes is very wide. This is the construction and repair of pipelines transporting liquid and gaseous substances. Polypropylene pipes are used for transportation of gases in heating systems, in sewerage networks, in sewerage systems. Polypropylene is chemically resistant to all substances.

Today, the demand for polypropylene pipes is very high and exceeds all produced volumes. Therefore, equipment for the production of polypropylene pipes will always be in demand.